bread page 2

Start/Stop button
This starts and stops the selected baking program.
Start
In order to start a program, press the "start/stop" button for approx 1 second. A short beep is heard
and the two dots in the time display begin to flash and the program starts.
Stop
In order to stop a program, press the "start/stop" button for approx 2 seconds until a beep
confirms that the program has been terminated.
OnlOff
Two dots flashing: Program is started.
Two dots continuously lit: Program is stopped.
Delay Timer
You can delay the time your bread maker starts to have fresh bread ready at a particular time. This
is ideal when you would like fresh bread when you get up in the morning or when you come home
from work Use the "Timer" button to advance the time in 10 minutes increments. If necessary,
use the "Timer" button to decrease the time. When the delay timer is set where you want it, make
sure to press the "Start/Stop" button. The colon";" flashes and your bread will be ready when you
planned.
The time that appears on the clock after it switches on automatically is the remaining baking time.
Therefore ensure you set the time for when you would like the bread ready. The maximum delay is
13 hours. "
For Example
It is 8:30pm and you would like your bread to be ready the next morning at 7 clock. ie in 10
hours and 30 minutes. Press the "arrow pointing upwards" until 10:30 appears, as the time
between "now"(8:30pm) and the time the bread should be ready is 10 hours and 30 minutes. If
you work with the delay timer option, do not use any easily perishable ingredients such as eggs,
fresh milk, etc,
Keep Warm
Your bread is kept warm for 60 minutes after baking. If you would like to take the bread out
during this time, switch the program off with the Start/Stop Button.
Warning display
If the display shows "H:HH" after you have pressed Start, the temperature inside is still too high.
Press Stop: open the lid and let the machine cool down for 10 to 20 minutes.
lf the display shows "E:EE"after you have pressed Start, the temperature sensor is disconnected.
The sensor must be checked by an authorized service agent.



开始/停止按钮
这将启动和停止所选择的烘烤程序。
开始
为了启动一个程序，按下“启动/停止”按钮约1秒钟。短哔的一声
而在时间显示的两个点开始闪动和程序启动。
停止
为了停止程序，按下“启动/停止”按钮约2秒，直到发出哔
确认该计划已被终止。
OnlOff
两点闪烁：程序已启动。
两个点连续亮：程序停止。
延时定时器
您可以耽误您的面包机开始有新鲜的面包准备在特定的时间的时间。这
是理想的，当你想新鲜的面包，当你早上起来或者当你回家
从工作中使用的“计时器”按钮，进入时间10分钟为增量。如果需要的话，
使用“计时器”按钮来减少所需的时间。当延迟计时器设置您想要的位置，使
务必按“开始/停止”按钮。冒号“;”闪烁，你的面包就准备好，当你
计划。
之后，它会自动切换上的时钟显示的时间是剩余的烘烤时间。
因此，确保你设置的时间当你想在面包准备。最大延迟是
13小时。 “
例如
这是下午8:30，您希望您的面包准备第二天早上7点。即10
小时和30分钟。按“箭头朝上”10:30之前出现，随着时间的
“现在”（下午8:30）与时间之间的面包应该准备好为10小时30分钟。如果
你有延时定时器选项工作时，不要使用任何容易易腐食材如鸡蛋，
鲜牛奶等，
注意保暖
面包保持温暖，烘烤60分钟后。如果你想利用面包出来
在此期间，与开始/停止键切换程序关闭。
警告显示
如果显示屏显示“H：HH”你按下Start后，里面的温度仍然过高。
按停止：打开盖子，让机器冷却10〜20分钟。
LF显示屏显示“E：电子工程专辑”你按下Start后，温度传感器断开。
传感器必须由授权的服务代理商进行检查。